Electrical Repair

The Opticom Control Module enables installers to configure the installation based on department use policy for emitter systems. The OCM provides precise triggering of the emitter modules based on operation of the front emergency lights, regardless of flash pattern. The OCM also provides a selectable manual pause or activation function utilizing the fairing speaker mute switch (speaker mute function then disabled). The unit connects with the side stand to pause when "parked". Indicator light outputs are also provided for either Paused or Activated function using optional indicator lights. The user decides based on preference or department policy. Make selection below regarding activation and indicator light wiring so that unit will be pre-set to those preferences.

Replacement / Optional Red LED Indicator for Opticom Module FMSA-EL-OCM.

Mating 8X plug connection for Opticom 795 emitter. Agencies have requested mating connection plugs to their Opticom units to mate with the FMS harness connections. Available with one free-hanging 8X pin housing and 4 pin connectors (only 3 are needed with the FMS system) mating to the factory Opticom plug. Use FMS Crimp Tool FMSA-EL-CTHR or equivalent to crimp the pins to the wire harness.

Siren / PA cable kit originally available from BMW for use in bypassing the PA cable inside the wiring harness of MY 2015+ R 1200 RT-P models. Used only for exceptional cases where PA background noise levels are too high from LIN interference in the wiring harness. Later 1200 / 1250 models utilized twisted-pair PA wires in the harness to further reduce background noise making this harness unnecessary. Formerly BMW PN 71 60 2 447 074 or 71 60 2 452 878

Power Management Module is a direct plug & play connection on 2010 through 2014 BMW R 1200 RT-P models (K26MU). The PMM provides a 30 minute timed power extension after ignition-OFF from the radio circuit, activated with ignition power. Two outputs from the PMM include one heavy circuit for radios and a lighter circuit for the helmet headset interface module. Unit includes proprietary BMW connectors. Formerly BMW PN 65 12 2 211 643 Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

Replacement Part: 20" Power Cable for FMS Accessories BT Amplifier. Depending upon which power source is available, power can be provided from either radio power supply plug, radar power plug, ACC 1-3 plugs on BMW plug strip or from lighter socket plug (when lighter socket / plug strip is removed). Replacement speaker cable. Note: If multiple devices are being powered by the radio circuit, you can use the FMS Power Plug Divider Code A harness to divide the circuit utilizing BMW connectors. Fits 2015 and later BMW R 1200/1250 RT-P models.

Replacement Part: Wire nuts for speaker wire connection with BT Amplifier. One each red & black trimmed nut provided. Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

FMS Accessories offers the male power socket plug that connects to the BMW accessory socket at the RH knee area or near the LH rear turn signal. Plug cover unscrews revealing both poles with a screw-type connection for your accessories. Very handy for spot lights, heated gear, chargers, etc. Formerly BMW PN 61 13 8 060 106

Special plug for 2019+ CHP motorcycle siren speaker connections to test speaker in workshop. Mutes speaker to volume suitable for environment with other workers. Warning: For workshop testing purposes only - not for use while riding motorcycle! Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

Kit containing two crimp-in diodes to resolve sporadic issues caused by reverse voltage from the BMW rear duplex emergency light. Kit is shipped without cost to agencies that have purchased ELM modules. Contact FMS at info@fmsaccessories.com to request your kit. Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

"Y" Harness for BMW ID lights in rear pod. Enables adding license plate ID lights by powering both rear pod ID lights from one flasher board output, enabling the other flash board output to power license plate mounted ID lights. Formerly BMW PN 77 50 2 475 080 (never stocked by BMW). Free shipping is limited to the continental United States. Shipping charges apply to international shipments.