ProLaser 3 Lidar Holster - Wire Form

$218.00

Locking PL-3 Lidar gun holster for BMW R 1200/1250 RT-P, standard with bracket for mounting on right or left side of 2006 through 2014 models. Fits 2015+ RT-P models by using the adapter plate shown below. Constructed of steel formed wire with welded mounting brackets and lock plate. Powder-coated for attractive finish. All locks are keyed the same for easy use within the agency. Formerly BMW PN 71 60 2 452 886 Requires mounting Adapter Plate for MY2015+ RT-P models.

Availability: In stock

SKU: FMSA-GHPL3-WF

Qty:

Add To Estimate

Note: If your protection bar is substantively bent in / back, you may not have sufficient clearance for this accessory to fit properly. Either bend your bar back out closer to the original position or replace the bar.

Free shipping is limited to the continental United States.

Shipping charges apply to international shipments.

Note: The addition of this or other accessories does not change the overall load limits of your motorcycle - always adhere to the manufacturer's recommendations for loading.

Customers who bought this item also bought

Handlebar Accessory Mounting Bolt Kit

FMSA-HBKS

FMS Accessories offers the bushing and bolt kit needed to mount various accessories to the handlebars on the K52 / 2015 - 2022 R 1200 / 1250 RT-P including radar remote controllers, microphone mounts, cell phone holders, etc. The kit includes a special aluminum bushing, stainless steel washer and pan-head stainless steel Torx head bolt. The kit is available in standard length as well as +5 mm and +10 mm longer bolts for use when multiple brackets are attached to one side. The M10 Torx head bolt already has encapsulated thread locker on the bolt end - the Torx head enables you to apply the required 40 Nm of torque as specified by BMW without deformation. Formerly BMW PN 71 60 2 452 841

$12.00

Radio Power Connection Plug Code A

FMSA-EL-RPP

BMW 2.5 mm high current plug to connect radios and other devices to the radio power plug on your BMW motor. BMW plug Code A (black housing) supplied with two sockets for 14 - 18 AWG wire connections (w/conductor & insulation crimps). Formerly BMW PN 71 60 2 452 887

$10.00

Radio Power Plug Divider

FMSA-EL-RPPD

Split the BMW 2.5 mm high current radio power connection (code A) on your BMW motors into two plugs when you need to use this power source to operate more than one item. Harness is made from high quality components with professional terminal crimps and PVC insulation over wires. BMW 2.5 mm Code A socket and pin housings (black) or Code B pin and socket housings (white). Code B is used to split the lighter socket power feed. Overall length: 5.5 inches Wire size: 16 AWG. New version with dual ATM fuse holders for faster installation of radios individually fused receiver and control head. Code A formerly BMW PN 71 60 2 452 880 Connector: BMW 2.5 mm Radio Power Connection Plug Code A. Note: Order two (2) mating Radio Power Connection Plugs with each Radio Power Plug Divider

$36.00

Radio Receiver Quick Mounting Plate

FMSA-MT-RQMP

An aluminum plate with slots and corresponding slot bolts that match the patterns in most radio receiver bracket mounting holes. This enables you to loosely mount the radio receiver mounting bracket, move it around until it is where you want it, when tighten it down without removing the radio box floor plate or drilling any holes. Attaches to threaded inserts in the radio box floor. Comes with stainless steel hardware. Formerly BMW PN 71 60 2 408 076 Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

$30.00

FMS Accessories

ProLaser 3 Lidar Holster - Wire Form

Are you sure to place the backorder?

Customers who bought this item also bought

Handlebar Accessory Mounting Bolt Kit

Radio Power Connection Plug Code A

Radio Power Plug Divider

Radio Receiver Quick Mounting Plate

Related products

Lidar Gun Holster Adapter Plate